BOSCH Placement Paper (Technical)

 

1. Critical stress at which material will start to flow

(a)yield

(b)ultimate tensile stress

(c) proof stress

(d) none o the above

 

2. maximum degree of freedom in space

Ans. 6

 

3. bearing which will take axial and radial loads.

(a) thrust bearing

(b) deep groove

(c) taper roller

(d) roller

 

4. volume of water per cubic meter of air.

(a)specific volume

(b) specific gravity

(c) vapour pressure

(d) none of above

 

5. fluid is flowing through a frustum of cone. what is the nature of graph of velocity Vs. c/s area. {flow = velocity X c/s area}

(a) parabola

(b) hyperbola

(c) y=mx+c

(d) x=x.

 

6. Fluid in a pipe having no change in profile with change in length of pipe ...explain type of flow.

a)Laminar

b)Turbulent

c)fully developed profile

d)steady flow

 

7. Which are correct

 

I) Navier Stokes Eq. is .... of momentum

conservation eq.

II)bernoulis eq. is for viscous flow

III) REYNOLD no. >3000 always for turbulent flow.

 

a)I and II correct

b)I and II not correct

c)II and III correct

d)II and III not correct

 

8. Which can't be removed during alloying from Fe

alloys

a) co

b) N

c) Si

d) As

 

9.There are two ropes burning non uniformly (rate) and clock half an hour each. which can't be clocked ?

a) 1 Hr.

b) 45 min

c)15 min

d)none

 

10. Lim n->0 (1+ 1/n)^n =

a) 1

b)0

c)e

d)infinity

 

11.time dependent increase in length at steady temp. is called

a) super plasticity

b) creep

c) fatigue

d) none

 

12. Viscosity change with increasing temp.

a) decreases

b) increases

c) same

d) first decreases and then increases.

 

13. Direction of friction in bicycle tyres

a) along motion

b) opp. motion

c) Front opp. motion and vice versa

d) rear opp. motion and vice versa

 

14. Sp. gravity of a fluid

a) density of fluid at 0`c / density of water at o`c.

b) density of fluid at 0`c / density of water at T`c.

c) density of fluid at T`c / density of water at o`c.

d) density of fluid at T`c / density of water at T`c.

 

15. lateral strain / longitudinal strain

a) Poission's Ratio

b) Bulk Modulus

c) Modulus Of Elasticity

d) None

 

16. 10 coins & 1 defected coin and 2 weighs Find min weighs req. to detect faulty coin

a) 2

b)3

c)4

d)5

 

17. 9 members in meeting scheduled at 10:00 A.M. , all reaches at 9:48 A.M. . one member req. 2 min to intro with other find meeting delay with scheduled time of 10:00 A.M..

a) 1 Hr.

b) 6 min

c) ...

d) At scheduled time

 

18. A completes job in 10 hr. and B completes in 15 hr.. Find when both together works

a) 6 hr.

b) 8 hr

c) 10 hr

d) none

 

19. A ball dropped from H height and moves 80% of height each time. Total dist. covered

a) 4H

b) 5H

c) 7H

d) 9H

 

20. A cantilever beam loaded at free end find reinforcement place

a) AT neutral axis

b) above neutral axis

c) below neutral axis

d) above and below neutral axis

 

21. punching a sheet of D diameter and T thickness and S ultimate tensile stress

a) 3.14 DTS

b) 3.14TS X D^2

c) 6.28 DTS

d)6.28 TS x D^2

 

Bosch Placement Paper Pattern

 

SECTION 1(TECHNICAL)

 

1. There was a figure of JK flip flop in which ~q is connected to J input and K=1. If clock signal is successively applied 6 times what is output sequence (q=?)

d) 010101

 

2. Frequency response of a filter is

a) Range of frequencies at which amplification of signal is employed.

b) Output voltage versus frequency (plot)

c) Filter which suppresses particular frequency

 

3. Gain and bandwidth of an op amp is

a) Independent of each other

b) Gain decreases as bandwidth decreases

c) Gain increases as bandwidth increases till some extent after which stability decreases

 

4. There was a figure of 4:1 MUX in which A and B are select lines. Inputs S0 and S1 are connected together and labeled as C where as S2 and S3 are connected together and labeled as D. Then which of the following is true?

a) Y= B+C

b) Y= A+C

c) Y= A+B

d) Y= C+D (Where Y is the output)

 

5. In step up transformer (or Step down? not sure) transformation ratio is 1:5. If the impedance of secondary winding is 16 ohm then what is the impedance of primary winding?

a) 80     b) 3.2

 

6. There was a circuit consisting of AC voltage source and one inductance. Inductance value=0.2mH (or 0.2uH or 0.2H not sure).AC voltage =150 sin (1000t).what is the current flowing in the circuit?

a) i= 7.5 sin (1000t)

b) i= -7.5 sin (1000t)

c) i= 7.5 cos (1000t)

d) i= -7.5 cos (1000t)

 

7. Power gain of an amplifier having i/p gain of 20W and output gain of 20mW is

a) 60         b) 25         c) 10         d) 0

 

8. There was a RC circuit given with AC voltage source. Expression for capacitance was asked for charging condition. Choices were somewhat like this: a) some value multiplied by exp (-t/T)

ans --c i= (Vs/R)exp(-t/ T)

 

9. 2?s complement of -17

ans -- 01111

 

10. Instrumentation amplifier is used for--------- --?

a). effective shielding

b). high resective filters

c). high common mode

d). all the above.

 

11. In ?ON CHIP? decoding memory can be decoded to

a) 2^n         b)2^n +1         c)2^n -1         d) some other choice

 

12. Half of address 0Xffffffff is

a) 77777777 b) 80000000 c) 7FFFFFFF d) some other choice

 

13. Which one of the following is used for high speed power application?

a) BJT         b) MOSFET         c) IGBT         d) TRIAC

 

14. One question related with SCR rotation angle given ifring angle is 30degree

ans - 150degree

 

15. SCR is used for

a) To achieve optimum (or maximum ...not sure) dv/dt

b) For high current ratings

c) To achieve high voltage

d) Some other choice

 

16. State in which o/p collector current of transistor remains constant in spite of increase in base current is

a) Q point         b) Saturation         c) Cut off

 

17. A 16 bit monosample is used for digitization of voice. If 8 kHz is the sampling rate then the rate at: which bit is transferred is

a) 128         b) 48         c)         d)

 

18. To use variable as recursive, variable should be used as

a) Static         b) Global         c) Global static         d) Automatic

 

19. what is the resonant frequency of parrel RLC circuit of R= 4.7 komh L= 2 micro Henry and c=30pf.

a). 20.5 MHz

b). 2.65 KHz

c). 20.5 KHz

d). none

 

20.for the parallel circuit (one figure is given) Is= 10mA. R1= 2R, R2=3R, R3= 4R. R is artritary

a). 3.076mA

b). 3.76mA

 

21. main ()

{

int a=0x1234;

a=a>>12;

a=a<<12;

printf (?%x?, a);

}

What is the output?

a)1000         b) 2000         c)         d) None of these

 

22. What does (*fun () []) (int) indicate?

ans...b). an array of pointer to a functions that an int as parameter and return int.

 

23. #define A 10+10

main ()

{

int a;

a=A*A;

printf (?%d?, a);

}

a) 100 b) 200 c) 120 d) 400

 

24. One more question related with ADC like voltage is 8 volts. freqency 2 Mega hz. what is the converssion rate

 

25. Question related with serial in parallel out shift register?What is output sequence?

Ans..... 1010

 

26. Given one RLC circuit in which values of R, L and C were given. What is the value of frequency f?

 

27. if (fun ())

{

X++;

}

X gets incremented if and only if

a) fun () returns 0

b) fun () return 1

c) fun () return -1

d) return a value other than 0

 

28. In dynamic memory

a) Power dissipation is less than that of static memory

b) Clock is needed

c) Refreshing is required

d) All the above

 

29. Short, int and long integers have how many bytes?

a)2,2,4         b) Machine dependant         c)2,4,8         d) Some other choice

 

30. A (n) is -----------filter combination of

a) Passive         b) Active         c) AMPLIFIER         d) BOOSTER

 

31.Mobility of electron is

a) Increases as temperature increases

b) Decreases as temp decreases

c) Independent of conductivity

d) Some other choice

 

32. Structure comparison is done

a). yes

b) no

c) compiler dependent

d)

 

33. The system in which communication occurs in both ways but not simultaneously in both ways is

a) Half simplex             b) Simplex         c) Half duplex         d) duplex

 

34. main ()

{

int a=5, b=6;

int i=0;

i=a>b? a:b;

printf (?%d?, i);

}

a) 0         b) 1         c) 6         d)

 

35. int fun (char c)

{

int i;

static int y ;}

a) c, i are stored in stack and y stored in data segment

b)c stored in stack and i,y are stored in data segment

c) c is stored in text segment, y in data and i in stack

 

36. main ()

{

int *p;

short int i;

p= (char *) malloc (i*10); (code was showing error here)

p+=10;

printf (?%d?, p);

}

Value of p?

 

37. main ()

{

int *p,i[2]={1,2, 3};

p=i;

printf (?%d %d %d?, i [0],*p,*p+1) ;

}

 

38. F = A'B' + C' + D' + E' then

A) F = A+B+C+D+E

B) F= (A+B)CDE

C) F = AB(C+D+E)

D) F= AB+C+D+E

 

39. how would you insert pre-written code into a current program?

a) #read<>

b) #get<>

c) #include<>

d) #pre<>

 

40.structure may contain

a) any other structure

b) any other structure expect themselves

c) any other structure except themselves and pointed to themselves

d) none of the above

 

41. three boys x,y,z and three girls x,y,z... sit around a round table . but x does not want any girl sitting to him and girl y does not want any boy sitting next. how many ways can they be seated.

a) 2

b) 4

c) 6

d) 8

 

42. k is brother of n and x. y is the mother of n and z is is the father of k . which of the following statement is not definitely true.

a) k is the son of z.

b) y is the wife of z.

c) k is the son of y.

d) n is the brother of x.

 

43. find the lateral surface of a prism with a triangular base if the perimeter of the base is 34 cm. and the height is 45 cm.

a) 765 square cm.

b) 3060 square cm.

c) 1530 square cm.

d) none

 

44.Given a< b< c < d . what is the max ratio of given equation

a) (a+b)/(c+d)

b) (b+c)/ (a+d)

c) (c+d)/ (a+b)

d) (a+c)/ (b+d)

 

45. A and B starts moving from points X and Y simultaneously at a speed of 5kmph and 7kmph to a destination point which is of 27 km from points X and Y. B reaches Y earlier than A and immediately turns back and met Z. Find the distance XZ.

ans.... 22.5 km

 

46. Ann is shorter than Jill and Jill is taller than Tom. Which of the following inferences are true?

a) Ann is taller than Tom         b)         c)         d) Data insufficient

 

47. A and B starts from same point at opposite direction. They will move 6km and take 8km left. How Far is A and B from each other?

ans ...20m

 

48.6440 soldiers are to be arranged in the shape of square. If 40 soldiers were kept out then the number of soldiers making each straight line is?

Ans --80

 

49. Sum of squares of two numbers is 404 and sum of two numbers is 22.Then product of two Numbers?

a) 20             b) 40             c)             d) (Answer is 40. Two numbers are 20 and 2)

 

50. In an examination 4 marks are assigned for correct answer and 1 mark is deducted for wrong answer. However one student attempted all 60 questions and scored 130.Number of questions he attempted correct is?

a) 35             b) 38             c) 42             d) 35

 

51. Each ruby is of 0.3 kg and diamond is of 0.4 kg.Ruby costs 400 crores and diamond costs 500 crores. Ruby and diamonds have to be put into a bag. Bag cannot contain more than 12 kg.Which of the following gives maximum profit (or in terms of wealth) (In crores)

ans ...only ruby 40p

 

52. the cpu stack is placed in ....

a). cpu resister

b). RAM

c). ROM

d). hard disk

 

53). (10 | 7) would produce

a). 17

b). 3

c). 11

d). 15

 

 

 

ENGLISH

 

Fill in the blanks...... .. the answers is :

 

61)             a). impounded             b). protected             c). hounded             d). relegated.

 

62).            a). oblinion             b). authertiory             c). dejection             d). deso.......

 

63).            a). subdued             b). bountiful             c). tentative             d). ardem.

 

64).            a).             b). esulcant             c). emblerratie             d). innate

 

65).    manor -- d). n. the landed estate of a land or nobleman.

 

66).    neologism -- c). n. giving a new meaning to an add word.

 

67).    batten -- b). n. a narrow strip of wood.

 

68).    tepid -- d). adj. lacking interest enhusi...., luewarm

 

69.     discerning -- d). adj. distinguishin one thing from another, having good judgment

 

Bosch Test Paper & Interview Pattern

 

 

 

•Duration of Test: 80 min

 

 

•Number of questions: 75

 

 

•Number of sections: 2

 

 

•No of questions in section 1: 50 (Technical)

 

 

•No of questions in section 2: 25 (General English)

 

 

 

NOTE:

1. This patter below is for computer science (CS) students only.

2. There was another set of paper for MECH branch students.

 

Section 1:

 

This section had only technical question. They were mainly from Pointers in C, C++, Data Structures and some questions on OS, DBMS. This section also had lots of question on bit conversions (HEX to Binary, decimal) and one question on finding 2's compliment and such others. There were few questions on finding TRUE/FALSE statement which was bit confusing. Question to calculate square root, cube root of a number were also included.

 

Overall, this section was easy if you are good with your basics. The questions were mainly around the basic concepts only. Each question had four options (A, B, C, D) and we had to find the most appropriate answer. Each correct answer carries 2 marks and there is a negative marking of 1 for each wrong answer. So be careful while attempting these questions.

 

Section 2:

 

This had only general English questions. No book will help you to answer these questions; instead you should have good knowledge of grammar and different English works.

 

There was a paragraph with some blanks in between. So we had to find the appropriate words to fill in, from the given options. Other question included comprehension, synonyms, proverbs type question and others.

 

This section needs some intelligent guessing as you feel that all of the given options are correct and sometime all are wrong. Each correct answer carries 1 mark and there is a negative mark of 0.5. Hope the information given by me here was useful to you.

 

 

TEST PATTERN:

 

Bosch patter was rarely available in this group, so I thought of sending this mail. This patter below is for computer science (CS) students only. There was another set of paper for MECH branch students.

 

Section 1:

This section had only technical question. They were mainly from Pointers in C, C++, Data Structures and some questions on OS, DBMS. This section also had lots of question on bit conversions (HEX to Binary, decimal) and one question on finding 2's compliment and such others. There were few questions on finding TRUE/FALSE statement which was bit confusing. Question to calculate square root, cube root of a number were also included.

 

Overall, this section was easy if you are good with your basics. The questions were mainly around the basic concepts only. Each question had four options (A, B, C, D) and we had to find the most appropriate answer. Each correct answer carries 2 marks and there is a negative marking of 1 for each wrong answer. So be careful while attempting these questions.

 

Section 2:

This had only general English questions. No book will help you to answer these questions; instead you should have good knowledge of grammar and different English works.

 

There was a paragraph with some blanks in between. So we had to find the appropriate words to fill in, from the given options. Other question included comprehension, synonyms, proverbs type question and others.

 

This section needs some intelligent guessing as you feel that all of the given options are correct and sometime all are wrong. Each correct answer carries 1 mark and there is a negative mark of 0.5. Hope the information given by me here was useful to you.

 

 

 

Interview Pattern - Robert-Bosch:

 

•Duration of Test: 80 min

 

•Number of questions: 75

 

•Number of sections: 2

 

•No of questions in section 1: 50 (Technical)

 

•No of questions in section 2: 25 (General English)

 

Note : Answers to be marked on the OMR Sheet.